From e7ab19d7ca25535087bf73c96e5df9479e6315dc Mon Sep 17 00:00:00 2001 From: "github-actions[bot]" <41898282+github-actions[bot]@users.noreply.github.com> Date: Tue, 18 Aug 2026 11:09:24 +0000 Subject: [PATCH] SMA EV Charger: add setup instructions (#32862) Co-authored-by: claude[bot] <41898282+claude[bot]@users.noreply.github.com> Co-authored-by: premultiply <4681172+premultiply@users.noreply.github.com> --- templates/definition/charger/semp-sma.yaml | 20 ++++++++++++++++++-- 1 file changed, 18 insertions(+), 2 deletions(-) diff --git a/templates/definition/charger/semp-sma.yaml b/templates/definition/charger/semp-sma.yaml index 9aa50305c..0962ff788 100644 --- a/templates/definition/charger/semp-sma.yaml +++ b/templates/definition/charger/semp-sma.yaml @@ -13,11 +13,27 @@ requirements: en: | Configure the SEMP base URL (`http:///SEMP`) and the device ID of the charger. IMPORTANT: The charger must NOT be registered directly as a consumer in the Sunny Home Manager / Sunny Portal at the same time! - The configuration option "Disconnect after full charge" must be disabled. + + Setup on the "SMA EV Charger": + 1. Set the rotary switch on the wallbox to PV/Eco charging. + 2. Deactivate the wallbox in the Sunny Portal (it can be added back via evcc later). + 3. Set "Operation with grid connection point meter" to "Yes" and set up a meter (SMA Sunny Home Manager 2 or Energy Meter) under "Configuration -> Parameters -> Meter configuration". This is required for the SEMP interface to be enabled. + 4. Set "Charging release via app" to "No". + 5. Set "Disconnect after full charge" to "No". + 6. Restart the device and wait for it to come back online. + 7. Add the charger in evcc and check/save the configuration (a vehicle may need to be connected for the SEMP interface to report the correct status). de: | Konfiguriere die SEMP Basis-URL (`http:///SEMP`) und die Geräte-ID des Chargers. WICHTIG: Der Charger darf NICHT gleichzeitig im Sunny Home Manager bzw. im Sunny Portal direkt als Verbraucher registriert sein! - Die Konfigurationsoption "Trennung nach Vollladung" muss deaktiviert sein. + + Einrichtung beim "SMA EV Charger": + 1. Drehschalter an der Wallbox auf PV/Eco-Laden stellen. + 2. Wallbox im Sunny Portal deaktivieren (kann später über evcc wieder hinzugefügt werden). + 3. "Betrieb mit Netzanschlusspunktzähler" auf "Ja" stellen und einen Zähler einrichten über "Konfiguration -> Parameter -> Zählerkonfiguration" (SMA Sunny Home Manager 2 oder Energy Meter). Erst dadurch wird die SEMP-Schnittstelle freigegeben. + 4. "Ladefreigabe über App" auf "Nein" stellen. + 5. "Trennung nach Vollladung" auf "Nein" stellen. + 6. Geräteneustart auslösen und warten, bis das Gerät wieder online ist. + 7. Die Wallbox in evcc anlegen und prüfen/speichern (eventuell muss ein Fahrzeug angeschlossen sein, damit die SEMP-Schnittstelle den richtigen Status zurückgibt). params: - name: uri description: